Product Introduction
• Nominal output: 125 VDC embedded rectifier subrack, 19-inch standard rack mounting
• Adopts high-frequency switching rectifier technology for AC-DC power conversion
• Supplies stable 125VDC power for substation protection relays, circuit breaker control coils, RTU, SCADA and other critical loads
• Integrates rectifier modules, monitoring unit, DC distribution and battery management
• Supports automatic float charge & boost charge for lead-acid / NiCd batteries
• Realizes N+1 redundant parallel operation, rectifier modules support hot swap

Specification
| Item | Specification |
|---|---|
| Nominal DC Output | 125 VDC |
| Output Voltage Adjust Range | 90 ~ 150 VDC |
| AC Input | 220VAC single phase / 380VAC three-phase, 45~65Hz |
| Power Factor | ≥0.99 |
| Peak Efficiency | ≥94% |
| Voltage Regulation Accuracy | ≤±1% |
| Output Ripple | ≤200mVpp |
| Redundancy Mode | N+1 / N+X parallel, active current sharing |
| Module Type | Hot-swappable rectifier modules |
| Communication | RS485 / SNMP / Modbus / DNP3 |
| Working Temperature | -40℃ ~ +55℃ (derating above 2000m altitude) |
| Storage Temperature | -40℃ ~ +70℃ |
| Relative Humidity | ≤90% RH, non-condensing |
| Protection | AC over/under voltage, DC overvoltage, overcurrent, short circuit, over-temperature, battery low voltage disconnect |
| Mounting | Standard 19-inch embedded rack |
| Battery Compatibility | VRLA flooded lead acid, NiCd battery |
Advantages
1. Modular & Hot-swappable Design
Rectifier modules can be replaced without powering down the whole system; capacity expansion is flexible by adding modules on site. No shutdown during maintenance, greatly reduce MTTR.
2. High Reliability N+1 Redundancy
Support automatic parallel current sharing. If one rectifier fails, remaining modules automatically take over full load, guarantee uninterrupted DC power for protection and control circuits.
3. Intelligent Battery Charging Management
Auto float charge, boost charge, temperature compensation charging. Effectively avoid over-charge or under-charge, extend battery service life and reduce battery replacement cost.
4. Remote Monitoring & Alarm
Built-in monitoring unit, support local LCD display and remote SCADA connection. Real-time view voltage, current, module status, alarm logs; remote parameter setting and fault notification.
5. High Efficiency & Low Harmonic
High PF, low THD, high conversion efficiency. Reduce energy loss and reactive power penalty, meet IEC power quality standards for power station and industrial sites.
6. Compact Embedded Structure
Standard 19-inch subrack, embedded installation in power cabinet, small footprint, front maintenance, convenient for new construction and renovation projects.

Value We Deliver to Customers
1.Guarantee Safety Operation of Primary Equipment
Stable 125V DC power ensures circuit breaker closing/tripping, protection relay and automatic control system work normally even during AC mains outage, preventing power grid accident expansion.
2.Cut Operation & Maintenance Cost
High efficiency reduces long-term electricity consumption; intelligent charging protects batteries; hot-swap and remote monitoring reduce on-site inspection and maintenance workload.
3.Flexible Capacity Planning
Users can configure the quantity of rectifier modules according to actual load and battery recharge current, expand capacity step by step with project growth, avoid over-investment in advance.
4.Unified Power Management
Integrated monitoring platform unifies the management of rectifiers, batteries and DC loads, centralized alarm and data upload, easy to access station SCADA system.
5.Wide Environmental Adaptability
Suitable for harsh industrial environments such as outdoor substation, rail tunnel, oil field, stable operation under wide temperature range.

FAQ
Q1: What batteries can this 125VDC rectifier subrack charge?
A: It supports VRLA lead-acid, flooded lead acid and NiCd batteries. Custom charge curve is available for special battery types.
Q2: What does N+1 redundancy mean for this system?
A: N means the number of modules needed to support full load + battery recharge current; +1 is one spare module. When one module fails, the rest can still fully carry the load without power interruption.
Q3: Can I replace the rectifier module when the system is running?
A: Yes. All rectifier modules are hot-swappable. You can pull out and replace faulty modules without cutting off the DC bus power.
Q4: What communication protocols are supported for remote monitoring?
A: Standard Modbus, RS485, SNMP, DNP3 are available, which can connect with SCADA, gateway and monitoring host for remote alarm and data collection.
Q5: Does the system need derating at high altitude?
A: Yes. Above 2000m altitude, power derating is required due to heat dissipation reduction. Please inform us of the site altitude before ordering.